PRODUCTS
VME MODULES
MODEL |
DESCRIPTION |
REMARKS |
ERT 1.51.01.0 |
VME-PC Interface can be operated by personal computers PC/AT (or compatible) types. Bi-directional connection between VME and PC bus. Optional 'piggy-back' 64k to 256k RAM without using any additional VME slot. |
6U |
ERT 1.51.02.0 |
PC-VME Control Board . (PC-resident) Up to eight VME-PC Interface (ERT 1.51.01.0) can be chained and controlled with a single board. The VME-PC bi-directional data transfer can be initiated only from this board (MASTER) |
Single slot in PC |
ERT 1.51.03.0 |
Cable Terminator Unit . Special terminating box connected to the end of the chain of ERT 1.51.01.0 units |
|
ERT 2.01.01.0 |
Quad Scaler . Four independent counter module with 8254-2 each. The three 16-bit counters of each 8254-2 can be chained to a single, 32-, or 48-bit counter. Continuous and GATED mode operation. |
6U |
ERT 2.05.01.0 |
64-bit Input Register |
6U Single slot |
ERT 2.08.01.0 |
Relay Adapter 2x32 contact |
6U Single slot |
ERT 2.12.01.0 |
64-bit Output Register |
6U Single slot |
ERT 2.23.01.0 |
Status Change Register . Intelligent monitoring (TMS320C25) of 16 independent states. Opto-isolated (1,5kV) inputs. Slave and master mode. 16k DATA RAM, 4k PROGRAM RAM, dual-port global memory 4k RAM. |
6U |
ERT 2.25.01.0 |
Parallel Input/Output Register . Two independent 16-bit register, one for Input, one for Output levels or pattern |
6U Single slot |
ERT 2.26.01.0 |
QDC Read-out Module . Receives and buffers data from QDCtransmitters (2x10 Input channels) 68-pin flat-cable connectors (GSI co-operation) |
6U Publ. 1. |
ERT 2.26.02.0 |
TDC-VME Read-out Module Receives and buffers data fromTDC Tower and controls Tower, 32-bit wide I/O, 64k RAM Operating modes: Data Acquisition, Programming and Test (GSI co-operation) |
6U Publ. 1. |
ERT 2.28.02.0 |
SLATE2 Module. (Second Level Architecture Test Environment) for detector emulation for LHC detectors.SLATE Mother Board (SMB) is connected to VME backplane, SLATE Daughter Board (SDB) contains High-Performance Parallel Interface (HIPPI) source engine, FIFO memory and control logic. Base Address selection, External Start and Clock connection. Four operating modes: stand-alone, slave, master, and daisy-chain. (CERN co-operation) |
6U |
ERT 4.04.01.0 |
4k Nuclear ADC. Resolution 4k,Conversion time: fixed 5us, Differential nonlinearity <1% Pulse Height Analysis,64k memory, 80186 processor control, RS232C Serial Port |
6U |
ERT 4.05.01.0 |
8-channel S&H-Input A/D Separate S&H for each input, Resolution 11 bits + sign, Conversion time 5us,S&H acquisition time <4us, Data read-out: single or blocktransfer |
6U |
ERT 4.05.02.0 |
8-channel FADC Resolution 14bit,speed: 20/40MSPS, SNR:74dB, Input (diff.)ampl.: +/-1,5V (full scale),DSP filtering and pre-processing |
6U |
ERT 4.06.21.0 |
4k Integrating ADC Floating input, Measurement of slowly- varying low- and medium level signals, 64k EPROM and64k RAM for control programs, 64k data RAM, Capable to control ERT 4.08.21.0 analog multiplexer. |
6U |
ERT 4.08.21.0 |
16-channel Multiplexer (analog MPX using relays), 5-wires switched, (twisted-pairs, guarded, ground independent and isolated from each other) |
6U |
ERT 4.10.02.0 |
32-channel 8 bit D/A |
6U Single slot |
ERT 5.01.01.0 |
Programmable Quad Timer . 10 MHz clock, four identical timer, three 16-bit counters and a 8-bit predivider in each |
6U |
ERT 5.03.01.1 |
16-channel Constant Fraction Discriminator (CFD) module separate 'anti-walk' setting, Output signals: symm. ECL, - forced air cooling and additional -5,2V 4A PS required - |
6U Publ. 7. |
ERT 5.03.02.2 |
16-channel Constant Fraction Discriminator (CFD) module separate 'anti-walk' setting, Output signals: symm. ECL, - forced air cooling and additional -5,2V 4A PS required - |
6U Publ. 7. |
ERT 9.01.01.0 |
Power Supply Module +5V/25A, +12V/4A, -12V/2A,+5Vstandby/1A(1,5Ah), mains/load stability:<0.5% |
6U 4 unit wide |
3U EURO MODULES
Nuclear Detector Signal Simulator (NDSS)
MODEL |
DESCRIPTION |
REMARKS |
SERT 1.15.01.0 |
Nuclear Detector Signal Simulator (NDSS) Controller Software support: NDSSDOS (DOS) NDSS LabWindows GUI (LabWindows) |
3U |
SERT 4.40.01.0 |
Nuclear Detector Signal Simulator (Analog Module)'Semi-Gaussian' shaping, ramp generator, random (Poisson) generator, Powered by SERT 9.01.02.0 |
3U |
SERT 9.01.02.0 |
Power Supply +/-15V, +5V (NDSS) |
3U |
Beam Position Monitor Electronics (BPM) 500MHz version
Publ. 2.
MODEL |
DESCRIPTION |
REMARKS |
SERT 3.04.01.0 |
RS-232 Twisted-Pair Serial Controller bi-directional converter between CAN-bus and standard RS-232 line.(used with SERT 4.05.01.0, BPMe DAQ, 500MHz BPM) |
3U |
SERT 4.05.01.0 |
BPMe DAQ (500MHz BPM) 8-bit Microcontroller with 8k ROM, 32k RAM, 10-bit digital control of SERT 4.16.01.0; 12-bit DAC, 12-bit ADC; data transfer rate 1Mbit/s (opto-coupled, twisted-pair half-duplex, asynchron) |
3U |
SERT 4.16.01.0 |
BPMe HF (500MHz BPM) Superheterodyne Receiver with LO, Synthesizer and Sequential Input Selection and Measurement at 500 +/- 2MHz, BW(HF): 5MHz, BW(IF): 220kHz, BW(Dem.): 500Hz, 200Hz, 100Hz, 50Hz; 4-Input Channel(Z0=50 Ohm) |
3U |
SERT 4.16.01.1 |
BPMe HF (500MHz BPM) [Modified sensitivity] Superheterodyne Receiver with LO, Synthesizer and Sequential Input Selection and Measurement at 500 +/- 2MHz, BW(HF): 5MHz, BW(IF): 220kHz, BW(Dem.): 500Hz, 200Hz, 100Hz, 50Hz; 4-Input Channel(Z0=50 Ohm) |
3U |
SERT 9.01.01.0 |
Power Supply +/-12V, +5V (500MHz BPM) |
3U |
SERT 9.01.01.1 |
Power Supply +/-12V, +5V (Low-noise version) |
3U |
500MHz Timing, Divider
MODEL |
DESCRIPTION |
REMARKS |
SERT 5.08.01.0 |
500MHz Timing, Divider finput:490-510MHz, division factors:1/2024, 1/184, 1/44 and 1/2. Outputs ECL/50Ohm each, Powered by SERT 9.01.03.0 |
3U |
SERT 9.01.03.0 |
Power Supply +12V/0.35A, +5V/1A, -5,2V/1A(500MHz Timing, Divider) |
3U |
VXI MODULES
Beam Position Monitor Electronics
Publ. 28.
MODEL |
DESCRIPTION |
REMARKS |
BPMeP |
Low-noise Preamplifier (pair) extremely low-noise broad-band preamplifier (1,5nV/sqHz, 50 kHz - to - 100 MHz),Input impedance: 500 kOhm/5 pF, Output impedance: 50 Ohm |
Special boxes |
BPMeA |
Analog Processing Module Sum and difference of theinput signals, programmable gain (0 -to- 66dB in 6dB steps), external LO-controlled moving frequency window (Bandwidth: 300kHz, 100kHz and 10kHz; gain:0, 6, 12, 18dB) |
6U |
BPMeD |
Digital Recording Module controls the operating modes of the BPMeA, 4 independent flash-ADCs (8bit/50ns), 4 fast FIFOs (4x4k/9bit) Controlled like a ''VME-VXI Slave' |
6U |
MULTIBUS-II MODULES
MODEL |
DESCRIPTION |
REMARKS |
MBRT 2.26.01.0 |
Intelligent Multibus-II Input/Output Board universal intelligent board with DSP (TMS320C25 40MHz).64k program memory, 62k data memory (32k dual-ported) Self-test,On-board P-bus interface for 'piggy-back' boards. Three timers, three scalers, 48-channel PIO, RS-232 port, |
6U |
MBRT 4.05.01.0 |
8-channel S&H ADC MBRT 2.26.01.0 extended with a8-channel S&H ADC Resolution: 11 bit + sign, Input range: -5V -to- +5V |
6U |
MBRT 4.10.01.0 |
8-channel D/A MBRT 2.26.01.0 extended with a8-channel D/A Resolution: 11 bit + sign, Short settling time, Output range: -10V -to- +10V |
6U |
NIM MODULES
MODEL |
DESCRIPTION |
REMARKS |
NEL 4.04.01.0 |
4096-channel Dual ADC technical parameters conform with PCA-4KND but in NIM mechanics |
Single width NIM |
NEL 4.16.01.0 |
16-Channel Shaper-Amplifier Low-noise, Programmable gain (2x -to- 1000x), Gain stored separately for each channel inNV-RAM, microcontroller used for download parameters and V24 control, Forced ventilation necessary |
Single width NIM |
NEL 4.16.02.1 |
16-Channel Fast Shaper-Amplifier Programmable gain(2x -to- 100x),. Gain stored separately for each channel in NV-RAM, microcontroller used for download parameters and V24 control. Doubled inputs (LEMO) on front panel, outputs at back panel, Forced ventilation necessary |
Single width NIM |
NEL 4.16.03.0 |
16-Channel Main & Fast Shaper-Amplifier Combined version of NEL 4.16.01 and 4.16.02, Common inputs (LEMO 50 Ohm),Separate outputs (multipin) |
Single width NIM |
NEL 4.20.01.0 |
8-Channel Dual Integrator Integrating 2 photomultiplier signals coming within a 0-to-15ns interval, Input rate:< 250kHzInput/Output connectors 50 Ohm (LEMO) |
Single width NIM |
NEL 5.03.02.1 |
6-Channel Constant Fraction Discriminator (CFD)Module dynamic range: 50:1, fraction:0,3; separate 'anti-walk' and threshold setting, negative NIM outputs, monitor outputs |
Single width NIM |
NEL 5.04.02.0 |
16-Channel Discriminator Module generates output pulses if the input pulses fall between the separately preselected upperand lower thresholds. Input ampl.: 0V - to - +8V. (5 kOhm). Master and slave operation, V24 interface, microcontroller control for separate threshold setting and communication. The module can be daisy-chained, and commonly controlled with modules type NEL 4.16.01.0 and NEL 4.16.02.0. |
Single width NIM |
NEL 8.20.01.0 |
2x16/32 ECL Fan-out Module high-speed fan-out for 2x16 symmetrical inputs to 2x32 symmetrical outputs,output jitter: < +/- 100ps |
Single width NIM |
IBM PC-based products
MODEL |
DESCRIPTION |
REMARKS |
PCA-4KN |
PC-based Multichannel Analyser Resolution:4k,conversions time: 5us, diff.lin.:< 1%. Software support: MCAFLEX (measurement and visualisation) GPeak Worksheet (peak evaluation) |
Single PC-board with 'Piggy-back' analog part |
PCA-4MX |
PC-based 4-Input Multiplexer co-operates with PCA-4KN |
Single PC-board |
PCA-4KND |
Dual Nuclear Multichannel Analyser GPeak Worksheet (peak evaluation) |
Single PC-board with two 'Piggy-back' analog boards |
PC-BIO-16/64 |
PC-resident Analog & Digital I/O-System 16,32,48 or 64 Input channels, processing of bipolar slowly-varying signals,4-channel DAC, 24 digital I/O-channel, programmable timer |
Single PC-board |
TPA and TPB |
Terminator Panels used with PC--BIO-16/64 Protectionand terminating of analog and digital inputs and outputs |
Special boxes |
DETECTOR ELECTRONICS
Charge Sensitive Preamplifiers
MODEL |
MAIN PARAMETERS |
REMARKS |
CSAMP a/b |
+/- 12V 1pF/400Mohm, Two parts, |
Two different |
CSPA 02 |
+/- 12V 1pF/1GOhm |
22x45mm board |
CSPA 02.01 |
+/- 12V 10pF/25MOhm |
22x45mm board |
CSPA 02.02 |
+/- 12V 10pF/25MOhm Output linear Range +8V -to- -8V |
22x45mm board |
CSPA 02.03 |
+/- 12V 1pF/2GOhm Output linear Range +8V -to- -8V |
22x45mm board |
CSPA 02.04 |
+/- 6 V 1pF/2GOhm Low-dissipation version |
22x45mm board |
CSPA 02M.04 |
+/- 6 V 1pF/2GOhm Low-dissipation (small outline) |
15x27mm board |
CSPA 02.04A |
+/- 6 V 1pF/200MOhm Low-dissipation version |
22x45mm board |
Preamplifier Power Supply
CSPS 02.0 |
+/- 12V dual output |
Special box |
CAMAC MODULES
More than 100 different types of
CAMAC modules, module list available on request.Last Update: 10-05-2013.